RORO skip hire acrossEnglandScotlandWales
0333 121 1056
Waste Collection · Production Sites

Industrial Waste Collection

Collections of production waste, offcuts, packaging and process residues from factories, workshops and yards, planned around how each waste stream is produced.

Industrial Waste Collection 0333 121 1056
  • Licensed local partners across England, Scotland and Wales
  • Waste paperwork provided with every job
  • Free, no-obligation quotes
Get a Quick Quote

Industrial waste is defined less by where it comes from than by how it behaves. A fabrication shop produces dense steel offcuts in small volumes; a packaging plant produces light trim by the lorry load; a food factory produces wet waste that cannot sit for long. Each needs a different vehicle, a different container at the point of production and a different destination, which is why industrial collections are specified stream by stream.

We arrange those collections through licensed local waste management and haulage partners, using whatever fits the material: cage vehicles and box vans for stillages and bagged waste, larger lorries for palletised or baled loads, and bulk vehicles where volumes justify them. Where a waste is classified as hazardous, it is routed through the appropriate specialist service with consignment notes rather than mixed into a general load.

Starting with the waste stream

The first conversation is about what comes off the process. We ask for a plain description of each waste, the form it takes (loose, bagged, baled, drummed, on pallets), how much accumulates over a week or a month, and whether it has been classified with a European Waste Catalogue code. If it has not, the producing process and any safety data sheets for the raw materials usually settle it.

That description decides everything downstream: whether the load is non-hazardous or hazardous, which facilities are authorised to accept it and what the carrier must write on the documents. Our pages on industrial waste and manufacturing waste describe the common streams.

Loaded collections from the shop floor or yard

A loaded collection suits waste that is produced in batches or stored in something that can be handled: stillages of offcuts, pallet boxes of rejects, cages of mixed packaging, bales of film or cardboard. The vehicle backs up to the loading door, the load goes on by hand or by your forklift, and the area is clear again within the visit.

Collections can be set to a fixed interval or called off when storage reaches an agreed level, subject to what local partners can offer. Sites short of yard space often prefer this to a standing container.

Where a RORO container is the better tool

Continuous production changes the sums. If waste leaves a line all day, moving it twice (into temporary storage, then onto a vehicle) costs labour that a container removes. A roll-on roll-off container stands by the process, is filled directly by tipping skips, forklifts or conveyors, and is swapped by a hook-loader lorry under a RORO skip exchange.

Light, bulky streams such as trim, packaging and insulation suit the 40-yard RORO; dense materials such as metal swarf or castings belong in the smaller sizes, part-filled, because the vehicle reaches its legal weight limit long before a large container is full. Payloads vary by container and local partner and are confirmed with your quote.

Segregation that pays for itself

Industrial sites have an advantage over most waste producers: their waste is consistent. The same offcut, the same wrap and the same pallet turn up every shift, which makes separation at source realistic. Clean metals have a scrap value, clean timber and cardboard cost less to process than mixed waste, and a general waste stream stripped of those materials shrinks.

We can arrange dedicated services for each: scrap metal collection, pallet and timber collection and cardboard collection, alongside the residual load. A short review under our waste segregation service will show which splits are worth making on your site.

Hazardous and restricted streams

Oils, coolants, solvent-based paints, contaminated rags and absorbents, chemical containers with residues, batteries and fluorescent tubes are common on industrial sites and none of them may go into a mixed load or a standard mixed-waste RORO. They are collected by carriers equipped for them, in suitable packaging, under a consignment note that travels with the waste. In Scotland the same materials are known as special waste.

Give us the details and we will route each one to the right service, whether that is hazardous waste generally or a specific collection such as oils and fuels.

Typical non-hazardous industrial loads

  • Production offcuts and trimmings
  • Rejected or out-of-specification product
  • Shrink wrap, strapping and polythene
  • Cardboard cores, sheets and cartons
  • Broken pallets, crates and dunnage
  • Clean metal offcuts and turnings
  • Non-hazardous dusts and sweepings in sealed bags
  • Redundant racking and benches

Collected separately as specialist waste

  • Waste oils, coolants and fuels
  • Solvents, paints, inks and adhesives
  • Oily rags, absorbents and filters
  • Containers holding chemical residues
  • Batteries and electrical equipment
  • Fluorescent tubes and lamps
  • Gas cylinders and aerosols
  • Asbestos-containing materials
These items can’t go in a standard RORO skip, but we can arrange a separate specialist collection.Get a quote →

Not sure? See our waste types guide or ask us when you book.

Sites we arrange collections for

  • Engineering and fabrication shops
  • Plastics and packaging plants
  • Food and drink producers
  • Printers and converters
  • Joinery and furniture makers
  • Vehicle and component manufacturers

Industrial Waste Collection – your questions answered

Can’t see your question? Call 0333 121 1056 or send us a message.

What is the difference between industrial and commercial waste?

Broadly, industrial waste comes from factories and industrial processes, and commercial waste from premises used for trade, business, sport, recreation or entertainment. Both carry the same duty of care. The practical difference is that industrial streams are more varied and more likely to need classifying individually before collection.

Do we need to know our waste codes before asking for a quote?

It helps, but it is not essential. A clear description of the process that produces the waste, its physical form and any safety data sheets for the materials involved is normally enough for the partner to confirm the correct code before the first collection.

Can collections be timed around production shifts?

We can ask for visits outside changeovers or dispatch peaks and will tell you what the local partner can offer. Collection windows depend on local availability and are confirmed when the service is booked, so please mention any gate hours or restricted periods at the start.

Our waste is dusty or lightweight. How is it transported?

Loose light material is bagged, baled or carried in an enclosed vehicle or container so that nothing escapes in transit. For regular volumes an enclosed RORO container is often the tidiest solution, as the load is covered from the moment it is tipped in.

Often booked with Industrial Waste Collection

Need more than one service for the same project? Add them to one enquiry and we’ll coordinate them together.

Get a quote

Get a Quick Quote

Tell us the site postcode, the waste, the container size if you know it, and when you need it. Mention exchanges, other sites or specialist waste and we will include them. Photos of the waste and the access help.

Prefer to talk? 0333 121 1056

ROROSkipHire.com is operated by Waste Cloud Ltd. Services are coordinated centrally and carried out by licensed local waste management and haulage partners across England, Scotland and Wales.